|
Dołącz teraz!
|
Dołącz już teraz do największej społeczności miłośników Forda w Polsce. Zarejestruj się i uzyskaj pełen dostęp do wszystkich działów, tematów i opcji jakie oferuje forum! |
|
Narzędzia wątku | Przeszukaj ten temat |
08-09-2023, 14:53 | #1 |
ford::amateur
Imię: Karol
Zarejestrowany: 17-07-2023
Skąd: Janow Podlaski
Model: Kuga
Silnik: 2.0l
Rocznik: 2010
Postów: 4
|
Błędy w modułach ABS, IC, RKE U0101-20
Z tymi bledami silnik pracuje normalnie auto nie jedzie bo jest brak reakcji na zmiane biegow(dct450) dopiero jak ostygnie to wszystko wraca do normy...
===PCM DTC U0415:86-A8=== Code: U0415 - Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A' Additional Fault Symptom (:86): - Signal Invalid Status (-A8 ): - Previously Set DTC - Not Present at Time of Request - Malfunction Indicator Lamp is On for this DTC Module: Powertrain Control Module Freeze Frame #1: -EVENT_TIME: 358845377 s (Fri Sep 08 11:49:23 2023) - Event time -TOTAL_DISTANCE: 188739 km - Total Distance -MODULE_VOLTAGE: 14.3 V - Control Module Voltage -ESTSERUN: No - Engine status - engine running -ESTSECRK: Yes - Engine status - engine in crank -INCAR_TEMPERATURE: 15 °C - In car temperature -OUTDOOR_TEMPERATURE: 15 °C - Outside temperature -PWR_MODE_KEY: Crank - Power Mode Key State -PWR_MODE_QF: Power Mode Undefined - Power Mode Quality Factor -LOAD: 11.76 % - Calculated Load Value -ECT: 82 °C - Engine coolant temperature -MAP: 99.0 kPa - Manifold absolute pressure sensor -RPM: 797 1/min - Engine Revolutions Per Minute -VSS: 0.0 km/h - Vehicle Speed -IAT: 24 °C - Intake Air Temperature -MAF: 0.60 g/s - Mass Air Flow -FRP: 32900.0 kPa - Fuel Rail Pressure -BARO: 98.0 kPa - Barometric pressure -APP_D: 0.00 % - Accelerator Pedal Position D ===END PCM DTC U0415:86-A8=== ===OBDII DTC U0415-C=== Code: U0415 - Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A' Status (-43): - Confirmed - malfunction is confirmed Module: On Board Diagnostic II ===END OBDII DTC U0415-C=== ===TCM DTC None=== Successful DTC reading, no error codes found Module: Transmission Control Module ===END TCM DTC None=== ===AWD DTC B2477-40=== Code: B2477 - Module Configuration Failure Status (-40): - DTC Maturing - Intermittent at Time of Request - Malfunction Indicator Lamp is Off for this DTC Module: All Wheel Drive Module Diagnostic Trouble Code details Module Configuration Failure ===END AWD DTC B2477-40=== ===ABS DTC C1233-A0=== Code: C1233 - Left Front Wheel Speed Sensor Input Signal Missing Status (-A0): - Previously Set DTC - Not Present at Time of Request - Malfunction Indicator Lamp is On for this DTC Module: Antilock braking system Diagnostic Trouble Code details The left front wheel speed sensor input signal is missing or the signal is not plausible. The code is set normally when the speed from one sensor differs from the speed on the other three sensors. The vehicle speed must exceed 40 kph (25 mph) for this code to be set. A fault has been reported. At some time a wheel speed signal has been out of range. The possible causes are as follows: Damaged wheel speed sensor. Sensor air gap too large. The vehicle has been towed on two wheels. A road wheel has been dynamically balanced on the vehicle while the IN2IGN iwas in position II or shortly after IN2IGN off. The vehicle has been driven on a two wheel rolling road. There is a short duration intermittent open circuit on the sensor wiring. The vehicle has been accident damaged or abused (eg. rolled spun parking brake turns etc.) The tires installed have varying outside diameters. A wheel bearing is worn or loose. Additional Information The ABS lamp should be illuminated. The ESP lamp should be illuminated. There will be an ESP malfunction warning displayed on the driver information text panel. ===END ABS DTC C1233-A0=== ===EPS DTC None=== Successful DTC reading, no error codes found Module: Electronic-Controlled Power Steering ===END EPS DTC None=== ===IC DTC U1900-20=== Code: U1900 - CAN communication bus fault Status (-20): - Previously Set DTC - Not Present at Time of Request - Malfunction Indicator Lamp is Off for this DTC Module: Instrument Cluster Diagnostic Trouble Code details CAN Communication Bus Fault - Receive Error Note: DTCs that start with 'U' are faults which occur during module-to-module communication. Modules should never be replaced based only on a 'U' code. These codes do not always indicate a problem, and can be caused by normal diagnostic functions, carried out on the vehicle. ===END IC DTC U1900-20=== ===PDM DTC None=== Successful DTC reading, no error codes found Module: Passengers Door Control Unit ===END PDM DTC None=== ===DFDM DTC None=== Successful DTC reading, no error codes found Module: Driver Door Control Unit ===END DFDM DTC None=== ===RCM DTC None=== Successful DTC reading, no error codes found Module: Restraint Control Module ===END RCM DTC None=== ===EATC DTC None=== Successful DTC reading, no error codes found Module: Electronic Automatic Temperature Control ===END EATC DTC None=== ===RKE DTC U0101-20=== Code: U0101 - Lost Communication With The TCM Status (-20): - Previously Set DTC - Not Present at Time of Request - Malfunction Indicator Lamp is Off for this DTC Module: Remote Keyless Entry ===END RKE DTC U0101-20=== ===GEM DTC None=== Successful DTC reading, no error codes found Module: Generic Electronic Module ===END GEM DTC None=== Ostatnio edytowane przez Karmag ; 09-09-2023 o 09:11 |
09-09-2023, 09:14 | #2 |
ford::amateur
Imię: Karol
Zarejestrowany: 17-07-2023
Skąd: Janow Podlaski
Model: Kuga
Silnik: 2.0l
Rocznik: 2010
Postów: 4
|
Odp: Błędy w modułach ABS, IC, RKE U0101-20
A tu log kiedy auto jest zimne i wszystko gra.
===PCM DTC None=== Successful DTC reading, no error codes found Module: Powertrain Control Module ===END PCM DTC None=== ===OBDII DTC None=== Successful DTC reading, no error codes found Module: On Board Diagnostic II ===END OBDII DTC None=== ===TCM DTC None=== Successful DTC reading, no error codes found Module: Transmission Control Module ===END TCM DTC None=== ===AWD DTC B2477-40=== Code: B2477 - Module Configuration Failure Status (-40): - DTC Maturing - Intermittent at Time of Request - Malfunction Indicator Lamp is Off for this DTC Module: All Wheel Drive Module Diagnostic Trouble Code details Module Configuration Failure ===END AWD DTC B2477-40=== ===ABS DTC None=== Successful DTC reading, no error codes found Module: Antilock braking system ===END ABS DTC None=== ===EPS DTC None=== Successful DTC reading, no error codes found Module: Electronic-Controlled Power Steering ===END EPS DTC None=== ===IC DTC None=== Successful DTC reading, no error codes found Module: Instrument Cluster ===END IC DTC None=== ===PDM DTC None=== Successful DTC reading, no error codes found Module: Passengers Door Control Unit ===END PDM DTC None=== ===DFDM DTC None=== Successful DTC reading, no error codes found Module: Driver Door Control Unit ===END DFDM DTC None=== ===RCM DTC None=== Successful DTC reading, no error codes found Module: Restraint Control Module ===END RCM DTC None=== ===EATC DTC None=== Successful DTC reading, no error codes found Module: Electronic Automatic Temperature Control ===END EATC DTC None=== ===RKE DTC None=== Successful DTC reading, no error codes found Module: Remote Keyless Entry ===END RKE DTC None=== ===GEM DTC None=== Successful DTC reading, no error codes found Module: Generic Electronic Module ===END GEM DTC None=== |